Hoval Root

CombiVal ER (200-1000)

CombiVal ER (200-1000)

Domestic water storage tank for heating domestic water. Steel tank, enamel painted on the inside, with protection against corrosion and thermal insulation. A built-in enamel painted heat exchanger.

Range of applications: heating with a heat source, ideally a gas, oil or biomass-based boiler - for new buildings and renovations.

Heating armature group mixer circuit flow left DN 20

Heating armature group mixer circuit flow left DN 20

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the right (heating flow / pump on left), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

HomeVent® ER (200-400)

HomeVent ER (200-400)

Comfort ventilation unit with self-regulating heat and humidity recovery for any installation positions. For installing units indoors and outdoors. Max. flow rate: 400 m³/h.

Range of applications: flats, single family homes - for new buildings.

TopTronic® E basic modules

TopTronic E basic modules

The basic modules control the heat generator and associated consumers, district heating systems or fresh water systems. These modules are normally already installed in the unit.

Range of applications: new buildings and renovations.

CombiVal ESR (200-400)

CombiVal ESR (200-400)

Domestic water storage tank for heating domestic water. Steel tank, enamel painted on the inside, with protection against corrosion and thermal insulation. A large built-in enamel painted heat exchanger.

Range of applications: heating with a heat source, ideally a heat pump or a gas, oil or biomass-based boiler - for new buildings and renovations.

Heating armature group mixer circuit flow left DN 25

Heating armature group mixer circuit flow left DN 25

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the right (heating flow / pump on left), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

HomeVent® ERT (250-450)

HomeVent ERT (250-450)

Internet-enabled comfort ventilation unit with heat and humidity recovery, all air connections at the top for upright installation. Max. air flow rate: 450 m³/h.

Range of applications: flats, single family homes - for new buildings.

TopTronic® E controller modules

TopTronic E controller modules

Modules for customised heating system design: from simple to complex. They can be used as stand-alone modules or in combination with one another.

Range of applications: heating circuits, hot water generation, solar plants, buffer storage tanks, measurement modules - for new buildings and renovations.

CombiVal ESSR (500-1000)

CombiVal ESSR (500-1000)

Domestic water storage tank for heating domestic water. Steel tank, enamel painted on the inside, with protection against corrosion and thermal insulation. A special built-in enamel painted heat exchanger.

Range of applications: heating with a heat source, ideally a heat pump or a gas, oil or biomass-based boiler - for new buildings and renovations.

Heating armature group mixer circuit flow left DN 32

Heating armature group mixer circuit flow left DN 32

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the right (heating flow / pump on left), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

TopTronic® E module expansions heating

TopTronic E module expansions heating

Module for expanding the functionality of standard systems. They are needed in addition to the basic modules.

Range of applications: heating circuits, energy monitoring, universal – new buildings and renovations.

Heating armature group mixer circuit flow right DN 20

Heating armature group mixer circuit flow right DN 20

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the left (heating flow / pump on right), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

TopTronic® E module expansions district heating

TopTronic E module expansions district heating

Module for expanding the functionality of standard district heating systems. They are needed in addition to the basic modules.

Range of applications: heating circuits, hot water generation, universal – new buildings and renovations.

Heating armature group mixer circuit flow right DN 25

Heating armature group mixer circuit flow right DN 25

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the left (heating flow / pump on right), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

TopTronic® E room control module

TopTronic E room control module

Modern colour touchscreen for intuitive operation of the TopTronic E system controller.

Range of applications: new buildings and renovations.

Heating armature group mixer circuit flow right DN 32

Heating armature group mixer circuit flow right DN 32

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the left (heating flow / pump on right), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

TopTronic® E GLT-Modul 0-10V

TopTronic E GLT-Modul 0-10V

Module for the analogue integration of the TopTronic E system controller into a SmartHome system or control network.

Range of applications: new buildings and renovations.

Heating armature group mixer circuit flow left / (right) DN 40-50

Heating armature group mixer circuit flow left / (right) DN 40-50

Compact armature group for transporting, mixing and adjusting the heating medium in the heating circuit. Installation on the left or right (heating flow / pump on right or left), thermally insulated.

Range of applications: can be combined with Hoval modular wall distributor - for new buildings and renovations.

HovalConnect Modbus

HovalConnect Modbus

Communication module for data exchange between the building management system and the Hoval TopTronic E system control via Modbus TCP or Modbus RS485 and license key for the HovalConnect online service.

Range of application: connection of a heating system with Hoval TopTronic E system controller to a building management system - for new buildings and renovations.

TopVal (130-160)

TopVal (130-160)

Storage tank located underneath or at side for heating domestic water. Steel tank, enamelled on the inside, with protection against corrosion and thermal insulation, with white foil jacket. A built-in heat exchanger.

Range of applications: heating with a heat source, ideally a TopGas gas boiler - for new buildings and renovations.

Charging/heating armature group direct/charging circuit DN 20

Charging/heating armature group direct/charging circuit DN 20

Compact armature group for transporting, mixing and adjusting the heating medium, for connecting a free-standing calorifier or as a direct heating circuit. Installation on the right (heating flow / pump on left), thermally insulated.

Range of applications: for new buildings and renovations.

HovalConnect KNX

HovalConnect KNX

Communication module for data exchange between your Smart Home System and the Hoval TopTronic E system control via KNX TP and license key for the HovalConnect online service.

Range of application: connection of a heating system with Hoval TopTronic E system controller to your Smart Home System - for new buildings and renovations.

Charging/heating armature group direct/charging circuit DN 25

Charging/heating armature group direct/charging circuit DN 25

Compact armature group for transporting, mixing and adjusting the heating medium, for connecting a free-standing calorifier or as a direct heating circuit. Installation on the right (heating flow / pump on left), thermally insulated.

Range of applications: for new buildings and renovations.

HovalConnect LAN

HovalConnect LAN

Interface module for connection of the TopTronic E system control to the router of the home network via a LAN cable and license key for the HovalConnect online service.

Range of application: online access to your heating system with Hoval TopTronic E system controller via a home network - for new buildings and renovations.

Charging/heating armature group direct/charging circuit DN 32

Charging/heating armature group direct/charging circuit DN 32

Compact armature group for transporting, mixing and adjusting the heating medium, for connecting a free-standing calorifier or as a direct heating circuit. Installation on the right (heating flow / pump on left), thermally insulated.

Range of applications: for new buildings and renovations.

HovalConnect LAN kit with room sensor

HovalConnect LAN kit with room sensor

Interface module for connection of the TopTronic E system control to the router of the home network via a LAN cable and license key for the HovalConnect online service.

Range of application: online access to your heating system with Hoval TopTronic E system controller via a home network - for new buildings and renovations.

Heating armature group direct/charging circuit DN 40-50

Heating armature group direct/charging circuit DN 40-50

Compact armature group for transporting, mixing and adjusting the heating medium, for connecting a free-standing calorifier or as a direct heating circuit. Installation on the right or left (heating flow / pump on left or right), thermally insulated.

Range of applications: for new buildings and renovations.

Industrial mobile data router

Industrial mobile data router

Industrial mobile data router for connecting the HovalConnect gateway or the Ethernet connection TopTronic E district heating com to the Internet, via LAN or WLAN. Metal casing, with Schuko mains adapter, top hat rail mounting clips, Ethernet cable (1.5 m), aerials: 2 x LTE, 1 x WLAN, without SIM card.

Range of application: professional use for installation in a control panel - new installations or expansions to existing plants.

HovalConnect WLAN

HovalConnect WLAN

Interface module for connection of the TopTronic E system control to the router of the home network via radio connection (WLAN) and license key for the HovalConnect online service.

Range of application: online access to your heating system with Hoval TopTronic E system controller via a home network - for new buildings and renovations.

Industrial Ethernet switch

Industrial Ethernet switch

Industrial Ethernet switch for connecting several Ethernet devices to one Internet access point. Metal casing, top hat rail mounting clips, without power supply unit.

Range of application: professional use for installation in a control panel - new installations or expansions to existing plants.

LG-2 Compact charging groups DN 25

LG-2 Compact charging groups DN 25

Compact armature group for transporting, mixing and adjusting the heating medium, for directly connecting to a free-standing calorifier , in the supply line or on the boiler, thermally insulated.

Range of applications: for new buildings and renovations.

HovalConnect WLAN kit with room sensor

HovalConnect WLAN kit with room sensor

Interface module for connection of the TopTronic E system control to the router of the home network via radio connection (WLAN) and license key for the HovalConnect online service.

Range of application: online access to your heating system with Hoval TopTronic E system controller via a home network - for new buildings and renovations.

RoofVent® RP

RoofVent RP

Supply and extract air handling unit with decentralised heat pump and high-capacity energy recovery for heating and cooling halls with high ceilings.
RoofVent® RH

RoofVent RH

Supply and extract air handling unit with high-performance energy recovery for heating high spaces.
RoofVent® RC

RoofVent RC

Supply and extract air handling unit with high-performance energy recovery for heating and cooling high spaces.
RoofVent® RHC

RoofVent RHC

Supply and extract air handling unit with high-performance energy recovery for heating and cooling high spaces in the 4-pipe system.
RoofVent® R

RoofVent R

Supply and extract air handling unit with high-performance energy recovery for high spaces.
RoofVent® RG

RoofVent RG

Supply and extract air handling unit with decentralised gas condensing boiler for heating spaces up to 25 m in height.
ProcessVent PV

ProcessVent PV

Compact unit for ventilating with heat recovery from process air.
ProcessVent PVH

ProcessVent PVH

Compact unit for ventilating and heating with heat recovery from process air.
ProcessVent PVC

ProcessVent PVC

Compact unit for ventilating, heating and cooling with heat recovery from process air.
TopGas® combi incl. RS-OT (21/18 - 32/28)

TopGas combi incl. RS-OT (21/18 - 32/28)

Low-cost gas condensing boiler for heating, with built-in hot water generation. Wall-mounted, continuous output adjustment, with basic controller.

Range of applications: flats, single family homes - for new buildings and renovations.

TopGas® classic incl. RS-OT (12-30)

TopGas classic incl. RS-OT (12-30)

Low-cost gas condensing boiler for heating and generating hot water. Wall-mounted, continuous output adjustment, with basic controller.

Range of applications: flats, single family homes, blocks of flats - for new buildings and renovations.

TopGas® combi (21/18 - 32/28)

TopGas combi (21/18 - 32/28)

Low-cost gas condensing boiler for heating, with built-in hot water generation. Wall-mounted, continuous output adjustment, with basic controller.

Range of applications: flats, single family homes - for new buildings and renovations.

TopGas® classic (12-30)

TopGas classic (12-30)

Low-cost gas condensing boiler for heating and generating hot water. Wall-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), without basic control.

Range of applications: blocks of flats, commercial buildings - for new buildings and renovations.

TopGas® classic incl. TTE (12-30)

TopGas classic incl. TTE (12-30)

Low-cost gas condensing boiler for heating and generating hot water. Wall-mounted, continuous power adjustment, with Hoval TopTronic E system controller.

Range of applications: flats, single family homes, blocks of flats – for new buildings and renovations.

TopGas® classic (35-80)

TopGas classic (35-80)

Low-cost gas condensing boiler for heating and generating hot water. Wall-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with basic control.

Range of applications: blocks of flats, commercial buildings - for new buildings and renovations.

TopGas® classic (100-120)

TopGas classic (100-120)

Low-cost gas boiler for heating and generating hot water. Wall-mounted, continuous output adjustment, with basic controller.

Range of applications: blocks of flats, commercial buildings – for new buildings and renovations.

UltraGas® (15-27)

UltraGas (15-27)

Gas condensing boiler for heating and generating hot water for the lowest possible operating costs. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: single family homes, dual occupancy homes, blocks of flats – for new buildings and renovations.

UltraGas® (35-100)

UltraGas (35-100)

Gas condensing boiler for heating and generating hot water for the lowest possible operating costs. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial buildings – for new buildings and renovations.

UltraGas® 2 (125-500)

UltraGas 2 (125-500)

Sophisticated gas condensing boiler for heating and generating domestic hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial, office and industrial buildings, schools and sports facilities, hotels – for new buildings and renovations.

UltraGas® 2 (530-1550)

UltraGas 2 (530-1550)

Sophisticated gas condensing boiler for heating and generating domestic hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial, office and industrial buildings, schools and sports facilities, hotels – for new buildings and renovations.

UltraGas® 2 multi-part installation (125-500)

UltraGas 2 multi-part installation (125-500)

Gas boiler for heating and generating hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control. For easier transportation when space is at a premium, assembled on site.

Range of applications: blocks of flats, commercial and office buildings, schools, hotels – for new buildings and renovations.

UltraGas® 2 multi-part installation (530-1550)

UltraGas 2 multi-part installation (530-1550)

Gas boiler for heating and generating hot water. Floor-mounted, continuous power adjustment, with Hoval TopTronic E system controller. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial and office buildings, schools, hotels – for new buildings and renovations.

UltraGas® 2 H (700-1550)

UltraGas 2 H (700-1550)

Sophisticated gas condensing boiler for heating and generating domestic hot water in tall buildings or district heating systems (max. operating pressure up to 10 bar). Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats above 50 m, office buildings over 50 m – for new buildings and renovations.

UltraGas® 2 DH (1400-3100)

UltraGas 2 DH (1400-3100)

Set consisting of two sophisticated gas condensing boilers and one shared flue gas line for heating and generating domestic hot water in tall buildings or district heating systems (max. operating pressure up to 10 bar). Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats above 50 m, office buildings over 50 m – for new buildings and renovations.

UltraGas® 2 D (250-1000)

UltraGas 2 D (250-1000)

Set consisting of two sophisticated gas condensing boilers and one shared flue gas line for heating and generating domestic hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial, office and industrial buildings, schools and sports facilities, hotels, local heating networks – for new buildings and renovations.

UltraGas® 2 D (1060-3100)

UltraGas 2 D (1060-3100)

Set consisting of two sophisticated gas condensing boilers and one shared flue gas line for heating and generating domestic hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial, office and industrial buildings, schools and sports facilities, hotels, district heating networks – for new buildings and renovations.

UltraGas® 2 D multi-part installation (250-1000)

UltraGas 2 D multi-part installation (250-1000)

Set consisting of two gas condensing boilers and one shared flue gas line for heating and generating hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control. For easier transportation when space is at a premium, assembled on site.

Range of applications: blocks of flats, commercial, office and industrial buildings, schools and sports facilities, hotels, local heating networks – for new buildings and renovations.

UltraGas® 2 D multi-part installation (1060-3100)

UltraGas 2 D multi-part installation (1060-3100)

Set consisting of two gas condensing boilers and one shared flue gas line for heating and generating hot water. Floor-mounted, continuous output adjustment, suitable for renewable gases (hydrogen and biomethane), with Hoval TopTronic E system control.

Range of applications: blocks of flats, commercial, office and industrial buildings, schools and sports facilities, hotels, district heating networks – for new buildings and renovations.

Belaria® pro comfort (8-15)

Belaria pro comfort (8-15)

Ground-breaking monoblock heat pump for heating and cooling and generating hot water. Outdoor installation, operating module inside the house, flow temperature up to 70 °C, modulating.

Range of applications: single family homes or dual occupancy homes - for new buildings and renovations.

Belaria® pro compact (8,13 /100/300)

Belaria pro compact (8,13 /100/300)

Ground-breaking monoblock heat pump for heating and cooling and generating hot water. Outdoor installation, compact indoor unit with integrated hot water and buffer storage tank, flow temperature up to 70 °C, modulating.

Range of applications: single family homes or dual occupancy homes - for new buildings and renovations.

Belaria® pro (24)

Belaria pro (24)

Ground-breaking monoblock heat pump for heating and cooling and generating hot water. Outdoor installation, operating module inside the house, flow temperature up to 70 °C, modulating.

Range of applications: single family homes or dual occupancy homes - for new buildings and renovations.

Belaria® fit (8-26)

Belaria fit (8-26)

Modulating monobloc heat pump in compact design for outdoor installation for heating and cooling in cascades and domestic hot water production, compact unit for outdoor installation.

Smart Grid-ready

Range of applications: Blocks of flats, industry, hotels, office buildings - for new buildings and renovations.

Belaria® fit (40-70)

Belaria fit (40-70)

Modulating air/water heat pump in compact design for outdoor installation. For heating and cooling in cascades of up to 16 machines, for efficient solutions with renewable energy, monovalent or as a hybrid system.

Range of applications: Blocks of flats, industry, hotels, office buildings - for new buildings and renovations.

Max-3 (420-2700)

Max-3 (420-2700)

Oil/gas boiler for heating, generating hot water and using process heat. With matching choice of controller. Ideal for Low NOx and standard oil or gas burners.

Range of applications: office buildings, commercial buildings, industrial buildings, local heating networks – for renovations.

MultiVal ERR (300-500)

MultiVal ERR (300-500)

Domestic water storage tank for heating domestic water. Steel tank, enamel painted on the inside, with protection against corrosion and thermal insulation. Two built-in enamel painted heat exchangers.

Range of applications: heating with two heat sources, e.g. a gas, oil or biomass-based boiler and a thermal solar plant - for new buildings and renovations.

TransShare

TransShare

Custom-made, turnkey, insulated distributor with distribution system in various hydraulic variants.

Range of applications: for any requirements - for new buildings and renovations.

Simply speak to our experts!

Max-3 plus (420-2700)

Max-3 plus (420-2700)

The Max-3 plus has a three pass design with dimpled tubes on the third pass fitted with additional retarders. This commercial Boiler which runs on gas, oil or dual fuel has a high fire efficiency to 95.2% net and gives low Nox emissions. As such it makes excellent economic and environmental sense. 

Max-3 plus boilers are available as heating only applications for medium to large commercial buildings. They are suitable for both new build and replacement projects. Maximum operating temperature is 105°and maximum working pressures is 6 bar.

MultiVal ESRR (500-1000)

MultiVal ESRR (500-1000)

Domestic water storage tank for heating domestic water. Steel tank, enamel painted on the inside, with protection against corrosion and thermal insulation. Two special built-in enamel painted heat exchangers.

Range of applications: heating with two heat sources, ideally a heat pump and a thermal solar plant - for new buildings and renovations.

TransShare Standarddesign

TransShare Standarddesign

For the TransShare standard design energy distributor, different heating circuits can be built onto the heating circuit distributor. An individual energy distributor can be assembled depending on the selected standard design.

Range of applications: for any requirements - for new buildings and renovations.

Simply speak to our experts!

TopVent® CH

TopVent CH

Recirculation unit as roof unit for heating tall spaces.
TopVent® CC

TopVent CC

Recirculation unit as roof unit for heating and cooling tall spaces in a 2-pipe system.
TopVent® CHC

TopVent CHC

Recirculation unit as roof unit for heating and cooling tall spaces in a 4-pipe system.
TopVent® TP

TopVent TP

Recirculation unit with decentralised heat pump for heating and cooling halls with high ceilings.
TopVent® TH

TopVent TH

Recirculation unit for heating high halls.
TopVent® TC

TopVent TC

Recirculation unit for heating and cooling high halls.
TopVent® THC

TopVent THC

Recirculation unit for heating and cooling high halls.
TopVent® SH

TopVent SH

Supply air unit as roof unit for ventilating and heating tall spaces.
TopVent® SC

TopVent SC

Supply air unit as roof unit for ventilating, heating and cooling tall spaces in a 2-pipe system.
TopVent® SHC

TopVent SHC

Supply air unit as roof unit for ventilating, heating and cooling tall spaces in a 4-pipe system.
TopVent® MH

TopVent MH

Supply air unit for ventilating and heating high spaces
TopVent® MC

TopVent MC

Supply air unit for ventilating, heating and cooling high spaces.
TopVent® MHC

TopVent MHC

Supply air unit for ventilating, heating and cooling high spaces.
TopVent® TV

TopVent TV

Recirculation unit for heating spaces up to 6 m in height.
TopVent® MG

TopVent MG

Gas-fired supply air unit for ventilating and heating rooms up to 25 m tall.
TopVent® TG

TopVent TG

Gas-fired recirculation unit for heating rooms up to 25 m tall.
TopVent® GV

TopVent GV

Gas-fired recirculation unit for heating rooms up to 6 m tall.
3-way valve YXG48.. PN 16, 130 °C DN 15-40

3-way valve YXG48.. PN 16, 130 °C DN 15-40

Three-way valve with cast iron valve body with threaded connection, incl. seals and screw connections and choice of suitable motor-based drives.

Range of applications: distribution, switching or mixing - for new buildings and renovations.

Balancing valve TN DN 20-32

Balancing valve TN DN 20-32

Valve for regulating and shutting off a volume flow, including a direct display at the bypass.

Range of applications: static, hydraulic comparison of solar plants – new buildings and renovations.

3-way valve VXG41.50, PN 16, 130 °C DN 50

3-way valve VXG41.50, PN 16, 130 °C DN 50

Three-way valve with gunmetal valve body with threaded connection, incl. seals and screw connections and choice of suitable motor-based drives.

Range of applications: distribution, switching or mixing - for new buildings and renovations.

Electrical flow rate meter VIG 2.5-10.0 m³/h

Electrical flow rate meter VIG 2.5-10.0 m³/h

For monitoring and measuring the volume flow using switching pulses. These are analysed by a control unit.

Range of applications: energy and heat monitoring, combined with Hoval TopTronic E system controller and solar controllers - for new buildings and renovations.

3-way valve VXF22.. PN 6, 130 °C DN 25-100

3-way valve VXF22.. PN 6, 130 °C DN 25-100

Three-way valve with cast iron valve body with flange connection inc. counter flanges, screws and seals and choice of suitable motor-based drives.

Range of applications: distribution, switching or mixing - for new buildings and renovations.

Flow rate sensor set plastic 0,9-150 l/min

Flow rate sensor set plastic 0,9-150 l/min

Set for measuring the flow rate and current temperature, plastic casing, electrically powered.

Range of applications: energy and heat monitoring, combined with Hoval TopTronic E system controller - for new buildings and renovations.

3-way valve VXF32.150, PN 10, 130 °C DN 150

3-way valve VXF32.150, PN 10, 130 °C DN 150

Three-way valve with cast iron valve body with flange connection inc. counter flanges, screws and seals and choice of suitable motor-based drives.

Range of applications: distribution, switching or mixing - for new buildings and renovations.

Flow rate sensor set brass 2-380 l/min

Flow rate sensor set brass 2-380 l/min

Set for measuring the flow rate and current temperature, brass casing, electrically powered.

Range of applications: energy and heat monitoring, combined with Hoval TopTronic E system controller - for new buildings and renovations.

2-way valve YVG48.. PN 16, 130 °C DN 15-40

2-way valve YVG48.. PN 16, 130 °C DN 15-40

Through valve with cast iron valve body with threaded connection, incl. seals and screw connections and choice of suitable motor-based drives.

Range of applications: control, shut-off - for new buildings and renovations.

2-way valve VVG41.. PN 16, 130 °C DN 50

2-way valve VVG41.. PN 16, 130 °C DN 50

Through valve with gunmetal valve body with threaded connection, incl. seals and screw connections and choice of suitable motor-based drives.

Range of applications: control, shut-off - for new buildings and renovations.

2-way valve VVF22.. PN 6, 130 °C DN 25-100

2-way valve VVF22.. PN 6, 130 °C DN 25-100

Through valve with cast iron valve body with flange connection inc. counter flanges, screws and seals and choice of suitable motor-based drives.

Range of applications: control, shut-off - for new buildings and renovations.

Ultrasound heat meter SHARKY 775 without MBus R ¾″-R 2″

Ultrasound heat meter SHARKY 775 without MBus R ¾″-R 2″

Counter for static measuring the amount of hot or cold energy transported based on the ultrasound principle, with external thread. Calculation unit with two temperature sensors, with battery power supply, without M-bus module. Nominal flow rates 1.5-10 qp.

Range of applications: installations in residential and commercial areas with water as the energy-carrying medium, consumption-dependent billing of energy costs - for new buildings and renovations.

2-way valve VC4613 / 230 V, PN 4, 95 °C DN 15-25

2-way valve VC4613 / 230 V, PN 4, 95 °C DN 15-25

Through valve with gunmetal valve body with female thread and motor-based drive with 1-wire control.

Range of applications: for new buildings and renovations.

Ultrasound heat meter SHARKY 775 with MBus R ¾″-R 2″

Ultrasound heat meter SHARKY 775 with MBus R ¾″-R 2″

Counter for static measuring the amount of hot or cold energy transported based on the ultrasound principle, with external thread. Calculation unit with 2 temperature sensors, with mains adapter with integrated MBus module for connecting to the system control TopTronic E. Nominal flow rates 15-60 qp.

Range of applications: installations in residential and commercial areas with water as the energy-carrying medium, consumption-dependent billing of energy costs - for new buildings and renovations.

Ultrasound heat meter SHARKY 775 without MBus DN 50

Ultrasound heat meter SHARKY 775 without MBus DN 50

Counter for static measuring the amount of hot or cold energy transported based on the ultrasound principle, with flange connection. Calculation unit with two temperature sensors, with battery power supply, without M-bus module. Nominal flow rates 1.5-10 qp.

Range of applications: installations in residential and commercial areas with water as the energy-carrying medium, consumption-dependent billing of energy costs - for new buildings and renovations.

Ultrasound heat meter SHARKY 775 with MBus DN 50-100

Ultrasound heat meter SHARKY 775 with MBus DN 50-100

Counter for static measuring the amount of hot or cold energy transported based on the ultrasound principle, with flange connection. Calculation unit with 2 temperature sensors, with mains adapter with integrated MBus module for connecting to the system control TopTronic E. Nominal flow rates 15-60 qp.

Range of applications: installations in residential and commercial areas with water as the energy-carrying medium, consumption-dependent billing of energy costs - for new buildings and renovations.

Electricity meter UEM

Electricity meter UEM

Corrosion-resistant design due to control damper made of chrome-nickel steel and casing made of special cast aluminium. For flue gas temperature of 400 °C (up to 900 °C for short periods, max. 15 minutes).

Range of application: individual energy monitoring in energy systems with energy consumers (e.g. heat pumps), as well as with energy producers (e.g. photovoltaic or CHP units) - new installations or expansions to existing plants.

ServeCool SWP

ServeCool SWP

Air conditioning unit for indirect free cooling with fresh air in combination with adiabatic and mechanical cooling, with integrated adiabatic pump
Thermalia® comfort (6-17)

Thermalia comfort (6-17)

Brine/water or water/water heat pump for heating and generating hot water. Indoor installation, flow temperatures up to 62 °C.

Range of applications: single family homes or dual occupancy homes - for new buildings and renovations.

Thermalia® comfort H (7,10)

Thermalia comfort H (7,10)

Brine/water or water/water heat pump for heating and generating hot water. Indoor installation, flow temperatures up to 67 °C.

Range of applications: single family home or dual occupancy homes – for new buildings and renovations.

Thermalia® twin (20-42)

Thermalia twin (20-42)

Two-stage brine/water or water/water heat pump for heating and generating hot water. Indoor installation, flow temperatures up to 62 °C.

Range of applications: mid-size residential, commercial, industrial or office buildings - for new buildings and renovations.

Thermalia® twin H (13-22)

Thermalia twin H (13-22)

Two-stage brine/water or water/water heat pump for heating and generating hot water. Indoor installation, flow temperatures up to 67 °C.

Range of applications: mid-size residential, commercial, industrial or office buildings - for new buildings and renovations.

Thermalia® dual (55-140)

Thermalia dual (55-140)

Brine/water or water/water heat pump with two separate refrigeration circuits for heating and generating hot water. Indoor installation, flow temperatures up to 62 °C.

Range of applications: larger residential, commercial, industrial or office buildings - for new buildings and renovations.

Thermalia® dual H (35-90)

Thermalia dual H (35-90)

Brine/water or water/water heat pump with two separate refrigeration circuits for heating and generating hot water. Indoor installation, flow temperatures up to 70 °C.

Range of applications: larger residential, commercial, industrial or office buildings - for new buildings and renovations.

Thermalia® dual R (55-140)

Thermalia dual R (55-140)

Brine/water or water/water heat pump with two separate refrigeration circuits for heating, cooling and generating hot water. Indoor installation, flow temperatures up to 62 °C.

Range of applications: larger residential, commercial, industrial or office buildings - for new buildings and renovations.

3-way valve B3G460, PN 10, 110 °C, without drive DN 15-50

3-way valve B3G460, PN 10, 110 °C, without drive DN 15-50

Three-way valve with brass valve body and female thread for manual operation or operation with motor-based drive.

Range of applications: mixing valve - for new buildings and renovations.

TM200, PN 10, 30-60 °C DN 20

TM200, PN 10, 30-60 °C DN 20

Thermostatic three-way mixing valve for regulating domestic water temperature. Brass valve body with external thread.

Range of applications: regulation of domestic water temperature - for new buildings and renovations.

JRG, PN 10, 45-65 °C DN 25-65

JRG, PN 10, 45-65 °C DN 25-65

Thermostatic three-way mixing valve for regulating domestic and heating water temperature. Valve body made of red brass with external thread or flange connection.

Range of applications: regulation of domestic and heating water temperature - for new buildings and renovations.

TransTherm® aqua L (1-10 - 1-50)

TransTherm aqua L (1-10 - 1-50)

Turnkey station for heating domestic water using the buffer storage principle. With stainless steel plate heat exchangers, copper soldering. Built-in TopTronic E system controller.

Range of application: high hot water requirements. Combination with CombiVal E or CombiVal C storage tank - for new buildings and renovations.

TransTherm® aqua L WT copper-free (1-10 - 1-50)

TransTherm aqua L WT copper-free (1-10 - 1-50)

Turnkey station for heating domestic water using the buffer storage principle. With stainless steel plate heat exchangers, copper-free. Built-in TopTronic E system controller.

Range of application: high hot water requirements. Combination with CombiVal E or CombiVal C storage tank - for new buildings and renovations.

CombiVal E (300-2000)

CombiVal E (300-2000)

Charging tank made of steel enamelled inside, with protection against corrosion and with thermal insulation for storing and for heating domestic water in combination with calorifier charging module.

Range of applications: combination with a heat source and the TransTherm aqua L or LS charging module - for new buildings and renovations.

CombiVal C (200-2500)

CombiVal C (200-2500)

Charging tank made from stainless steel with thermal insulation for storage and heating of domestic hot water in combination with calorifier charging module.

Range of applications: combination with a heat source and with the TransTherm aqua L or LS charging module - for new buildings and renovations.

TransTherm® aqua F (6-10 - 6-50)

TransTherm aqua F (6-10 - 6-50)

Turnkey station for heating domestic water using the continuous flow principle. With stainless steel plate heat exchanger, copper-soldered. Wall-mounted, TopTronic E system controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with an energy buffer tank. Flats, single family homes - for new buildings and renovations.

TransTherm® aqua F WT copper-free (6-10 - 6-50)

TransTherm aqua F WT copper-free (6-10 - 6-50)

Turnkey station for heating domestic water using the continuous flow principle. With stainless steel plate heat exchanger, copper-free. Wall-mounted, TopTronic E system controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with an energy buffer tank. Flats, single family homes – for new buildings and renovations.

TransTherm® aqua F (6-60 - 6-90)

TransTherm aqua F (6-60 - 6-90)

Turnkey station for heating domestic water using the continuous flow principle. With stainless steel plate heat exchanger, copper-soldered. Mounted on a stand frame, with built-in TopTronic E system controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with an energy buffer tank. Blocks of flats, commerce, industry - for new buildings and renovations.

TransTherm® aqua FS (7-10 - 7-90)

TransTherm aqua FS (7-10 - 7-90)

Turnkey station for heating domestic water using the continuous flow principle. With two stainless steel plate heat exchangers, copper soldering. Mounted on a stand frame, with built-in TopTronic E system controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with two buffer storage tanks. Flats, single family home - for new buildings and renovations.

TransTherm® aqua FS copper-free (7-10 - 7-40)

TransTherm aqua FS copper-free (7-10 - 7-40)

Turnkey station for heating domestic water using the continuous flow principle. With two stainless steel plate heat exchangers, copper-free. Mounted on a stand frame, with built-in TopTronic E system controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with two buffer storage tanks. Flats, single family home - for new buildings and renovations.

TransTherm® aqua FT (65)

TransTherm aqua FT (65)

Turnkey station for heating domestic water using the continuous flow principle. With stainless steel plate heat exchanger, copper-soldered. Wall-mounted, built-in thermal controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with an energy buffer tank. Flats, single family homes - for new buildings and renovations.

TransTherm® aqua FTC (57)

TransTherm aqua FTC (57)

Turnkey station for heating domestic water using the continuous flow principle. With stainless steel plate heat exchanger, copper-soldered. Wall-mounted, built-in thermal controller.

Range of applications: centralised or decentralised domestic water heating with high hygiene standards, combined with an energy buffer tank. Single family homes, dual occupancy homes - for new buildings and renovations.

Switching ball valve VBI60.. PN 40, 120 °C DN 15-50

Switching ball valve VBI60.. PN 40, 120 °C DN 15-50

Switching ball valve with brass ball valve body with threaded connection.

Range of applications: switching - for new buildings and renovations.

2-way ball valve VAG60.. PN 16, 120 °C DN 15-50

2-way ball valve VAG60.. PN 16, 120 °C DN 15-50

Straight way ball cock with brass ball cock body with threaded connection, incl. seals, screw connections and a cap and choice of suitable motor-based drives.

Range of applications: shutting off, switching - for new buildings and renovations.

EnerVal (100-2000)

EnerVal (100-2000)

Steel buffer storage tank for storing heating water. Steel storage tank with thermal insulation.

Range of applications: single family homes or dual occupancy homes - for new buildings and renovations.

EnerVal (800-2000)

EnerVal (800-2000)

Steel buffer storage tank for storing heating water. Steel storage tank with thermal insulation.

Range of applications: single family homes or dual occupancy homes - for new buildings and renovations.

EnerVal G (800-6000)

EnerVal G (800-6000)

Steel buffer storage tank for storing heating water. Steel storage tank with thermal insulation.

Range of applications: blocks of flats, commercial settings - for new buildings and renovations.

EnerVal G cool (800-6000)

EnerVal G cool (800-6000)

Steel buffer storage tank for storing heating water. Steel storage tank with thermal insulation.

Range of applications: blocks of flats, commercial settings - for new buildings and renovations.

Reflex N, wall installation, 6 bar, 70 °C N 8-25

Reflex N, wall installation, 6 bar, 70 °C N 8-25

Container with diaphragm and nitrogen cushion for static pressure control with threaded connection, wall installation.

Range of applications: closed heating and cold water systems - for new buildings and renovations.

Reflex N, floor installation, 6 bar, 70 °C N 35-1000

Reflex N, floor installation, 6 bar, 70 °C N 35-1000

Container with diaphragm and nitrogen cushion for static pressure control with threaded connection,free-standing model with feet (wall installation possible up to N 80).

Range of applications: closed heating and cold water systems - for new buildings and renovations.

Reflex F flat-form vessel, wall installation, 6 bar, 70 °C F 18-24

Reflex F flat-form vessel, wall installation, 6 bar, 70 °C F 18-24

Flat container with diaphragm and nitrogen cushion for static pressure control with threaded connection, wall installation.

Range of applications: closed heating and cold water systems - for new buildings and renovations.

Reflex C disc shape, wall installation, 6 bar, 70 °C C 18-80

Reflex C disc shape, wall installation, 6 bar, 70 °C C 18-80

Disc-shaped container with diaphragm and nitrogen cushion for static pressure control with threaded connection, wall installation.

Range of applications: closed heating and cold water systems with anti-freeze agent up to 50 % - for new buildings and renovations.

Reflex S solar wall/floor installation, 10 bar, 70 °C S 8-600

Reflex S solar wall/floor installation, 10 bar, 70 °C S 8-600

Container with diaphragm and nitrogen cushion for static pressure control with threaded connection, type S 8-33 wall installation, type S 50-600 floor-mounted with feet.

Range of applications: solar plants or closed heating and cold water systems with anti-freeze agent up to 50 % - for new buildings and renovations.

Reflex V intermediate tank, wall/floor installation, 10 bar, 120 °C V 6-350

Reflex V intermediate tank, wall/floor installation, 10 bar, 120 °C V 6-350

Intermediate tank with threaded connection in type V 6-60 or flange connection in type V 200-350. Type V 6-20 wall installation, type V 40-350 floor-mounted with feet.

Range of applications: temporary storage solution for added volume caused by increasing temperature, buffer storage tank - for new buildings and renovations.

Sludge separator with magnet MB3/L DN 25-50

Sludge separator with magnet MB3/L DN 25-50

Casing and connections made of brass, for fast and continuous removal of ferromagnetic and non-magnetic dirt and sludge particles.

Range of applications: plants with water (max. glycol content of 50 %) - for new buildings and renovations.

Sludge separator with magnet BE DN 50-100

Sludge separator with magnet BE DN 50-100

Casing and connections made of steel (St 37.2), for fast and continuous removal of magnetic and non-magnetic dirt and sludge particles from heating or cooling circuits. Max. operating pressure: 10 bar.

Range of applications: plants with the medium water or water/glycol (50/50 %) - for new buildings and renovations.

System water protection filter FGM, FF 050-200

System water protection filter FGM, FF 050-200

Magnetic protection filter for filtration of heating and cooling water, with high filtration capacity for corrosion particles and dirt. Filter head and bowl in brass.

Range of applications: for new buildings and renovations.

Hydraulic switch with deaerator MHK DN 25-32

Hydraulic switch with deaerator MHK DN 25-32

Hydraulic switch for disengaging flow rate in heat generators and for separating air, gas and dirt from the heating medium. Thermally insulated, with automatic ventilation.

Range of applications: systems with multiple heat generators, even solar, plants, can be combined with Hoval modular wall distributor - for new buildings and renovations.

Hydraulic switch with deaerator MH DN 40-200

Hydraulic switch with deaerator MH DN 40-200

Hydraulic switch for the hydraulic separation of multiple independent heat generators from the heating circuits. Thermally insulated, with automatic ventilation.

Range of applications: systems with multiple heat generators, even solar plants - for new buildings and renovations.

PHE welded

PHE welded

Danfoss plate heat exchanger with new Micro Plate technology.

Suitable for systems with Hoval Thermalia, UltraSource, Belaria pro heat pumps and further applications with system separation. - for new buildings and renovations.

PHE screwed

PHE screwed

SONDEX plate heat exchanger

Suitable for system separation in systems with Hoval Thermalia, UltraSource and further applications. - for new buildings and renovations.